Denafrips Terminator dac - 又是一部巨人殺手！

CKKeung

Denafrips Terminator dac 近期得了 www.6moons.com 的好評  :
http://www.6moons.com/audioreviews2/denafrips/1.html

小弟的一位朋友看了 review 後十分身痕。  
但 Denafrips 在香港冇代理，朋友只好從星加坡総公司買入。
雖然淘淘有得賣，也平啲，但星加坡総公司有三年保養，比較安全。

這相片是開箱開聲不足 2小時所拍的：


初步感覺是 : 嘩嘩嘩！  

www.6moons.com 的 Blue Moon Award 並非是浪得虛名的！
待 Terminator 煲熟一點再向各 hiendy 師兄作詳細報告！

CKL

Smart choice! I am a happy Pontus user. Waiting for the report.

treasury2014

上面那部是泉。

safin

睇機內部幾重料

ConstantK

佢外型好靚仔，再加上CKKeung師兄的"初步感覺是 : 嘩嘩嘩！"，期待詳細報告

rocmanb

嘩！好重料喎

Skycam

好有興趣喎

banjo

個電容陣真係壯觀, 期待報告.

dekiller

R2R到底好不好還是個疑問。但是R2R好像也不小。有人可以解釋一下嗎？

jackt

如果接受R2R啲聲，咁R2R咪好囉！唔如果唔鐘意嘅，咁就有千百萬種理由，去到最尾都係睇個人喜好，沒有對與錯的。

sealteam4

好像好吸引人

alvin1118

多谢大家支持，唔该晒！

Rgds,
Alvin
www.vinshineaudio.com

嚦嚦

First time heard of this brand, built quality is certainly impressive.

petermok387

dekiller 發表於 2017-10-31 11:57
R2R到底好不好還是個疑問。但是R2R好像也不小。有人可以解釋一下嗎？

I think the resisters used in R2R is able to carry more Current than those in the Chips. Hence the sound we hear is different between the Two. Hope some Professionals in this field can give some other explanations.

shooter

題外話
部機我都有興趣, email 去佢地公司間過點解d電阻要人手焊, 佢回覆話係公司秘密.....

我sent d相比自己相熟既打料廠睇過, 佢話睇相一定人手焊過, 咩原因就唔知啦
個人估計係d hi-precise resistor價錢高, 唔敢比SMD廠打......
不過人手焊料可以話百害而無一利

elo

shooter 發表於 2017-10-31 14:21
題外話
部機我都有興趣, email 去佢地公司間過點解d電阻要人手焊, 佢回覆話係公司秘密.....

Agree the SMD resistors seems were hand soldered rather than went through reflow oven after checking the photos on 6moons.  May be on that particular board the solder joints' wetting were not good after reflow so they used soldering iron to do the touch up...  You can see the alignment of the resistors were quite uniform, I think they were pick-and-placed by machine and not by hand.

And as it is just a consumer grade product, touch up is acceptable...Just a wild guess.

momei

You may see the built quality of the Holo Spring DAC:

https://item.taobao.com/item.htm ... amp;id=527818416876

at 1/3 of the price.

shooter

elo 發表於 2017-10-31 17:26
Agree the SMD resistors seems were hand soldered rather than went through reflow oven after checki ...

行業內用手工焊板, 主要喺ES階段, 因為做debug, f/w & s/w tuning.....通常手焊幾塊試function, UI and ME fitting.....

手工焊板最驟忌係溫度, 時間控制, 咁精準既電阻, 隊支辣鷄落去, 有咩side effect真係唔知.
所有SMD零件spec都有個reflow profile, 用打料機&過爐當然可以set到跟規格去做, 出錯機會近乎0. 除非搵中一間山寨到不得了既SMD factory做, 否則呢個工序出間題微乎其微.......

如果塊PCBA真係做完pick & place, reflow, 然後再用人手焊多次就重大劑 即係話有兩種錫料

tjausw

一睇就知呢部機係市場上之巨人殺手，冇得輸，6 moon........極少老點的!!!!!!!

tjausw

佢嘅電源供應係超晒班，極發燒之線路。