EQ setting sub仔正確設定(求救809 室內校正Error)

chung5

滿心歡喜試條新sub線,換線後run 一次Audyssey MultEQ , 點之結果係subwoofer detect error    , 之後換返舊線都係一樣....ching 們要點做?


use sunfire hrs 12

滿心歡喜試條新sub線,換線後run 一次Audyssey MultEQ , 點之結果係subwoofer detect error {:1_331:}   , 之後換返舊線都係一樣....ching 們要點做?

use sunfire hrs 12

結合各ching and 建議並取得成功之設定

EQsetting sub仔(sunfire hrs)正確設定:
心情唔好太緊張，講下笑放鬆D
1) input 係入L 先再入R ,用凳仔黎託住隻mic
2) auto setup前隻sunfire應該set返crossover bypass同level要0db喎
3) 張個超底音音量調細音量(可能係調大)同螢光幕提示個DB一樣

bigpun1975

pink noise 有冇聲? 會唔會覺得D Pink noise 好似冇セ力咁??

chung5

what is pink noise ar ching

bigpun1975

chung5 發表於 2012-3-5 13:54
what is pink noise ar ching

即係 amp  入面個 test tone, 嘈到PK 嗰D 聲

chung5

yes ha have sound for sub

chung5

好似弱咗dd

bigpun1975

chung5 發表於 2012-3-5 14:29
好似弱咗dd

你條訊號線一出一定一出二?
點駁法?
背面点set?
用セ電源線?

chung5

use 1 to 2
all use normal
and orginal pc

bigpun1975

chung5 發表於 2012-3-5 14:43
use 1 to 2
all use normal
and orginal pc

input 係咪入L 先再入R ?

bigpun1975

chung5 發表於 2012-3-5 14:43
use 1 to 2
all use normal
and orginal pc

咩訊號線?

bigpun1975

同埋我見你vol. 摟到二點鐘, 有冇試過摟細D 呀? 有機會係auto set up 時 test 到太大聲, 連-12 vol. 都出唔到75db, 有機會出error!

chung5

ok ching i go home try try.sin maybe you ar right

yuppi

chung5 發表於 2012-3-5 14:29
好似弱咗dd

因為係 WWO6, 你仲要用6米, 應該弱咗超過 一半以上...

ryanenen

yuppi 發表於 2012-3-5 15:59
因為係 WWO6, 你仲要用6米, 應該弱咗超過 一半以上...

無問题, 我用上9m rca重耍用rca 駁插, channel balance 比多少少巳無問題.

chung5

ching i back home try , 跟各ching 所講的去set ..結果係 sub woofer pass , but left defect fail ....{:1_250:} 冇理由.....左聲道會 fail 再試一次 最後得ok all done{:1_335:}

結論:  可能setting超底音音量調細音量(可能係調大)同螢光幕提示個DB不一樣 再加上天氣潮濕有關,否則 冇理由.....左聲道會 fail 加上上次tv去amp ARC 事件以經係第二次809有問題

最後多謝各位ching幫手留言救急{:1_347:} 對於av 新手的我又學會更多

KITCHAN

我以前試過用條45尺既十仔缐
都冇問題喎
又或者我木耳聽唔出啦


- 發送自我的 iPhone 大板凳應用

alzard

For those using HRS series subwoofer, please read page 7 of your manual carefully.
http://www.sunfire.com/manuals/HRS_manual_revB.pdf

6. Line-Level Inputs
These connect with RCA type cables from the line-level outputs of your receiver or preamp. Here are two examples:

If your processor or receiver has a single subwoofer output, connect it to the subwoofer’s left input jack (see page 11). There is no need to use the subwoofer’s right input jack.

If your processor does not have a subwoofer output, use “Y” adapters at the processor outputs (see page 12). In this way, you can send the processor’s full-range output signals to your main amplifier and to the subwoofer at the same time.