DIY SPEAKER.

medjohn

最近想DIY speaker. 想請教哪裡有賣全新speaker 單源？
Thanks!

tonyx

應泰貿易有限公司

http://www.lcy.com.hk/chi/contact.php

ccli1996

My spk driver units were all bought from Taobao.

medjohn

Is there any focal jm lab driver or Seas speaker available in hk?
Thanks

ccli1996

medjohn 發表於 2013-7-18 16:44
Is there any focal jm lab driver or Seas speaker available in hk?
Thanks

Not sure for focal driver but for Seas units, the last time I can buy it is from a 2nd-floor shop in SSP which was already closed for few years ago
I need to buy Seas drivers from Taobao early this year for my new built spk.
If you have concern on Taobao, maybe you can try from overseas dealers, say Madisound (from US) & Europe-audio or Jantzen audio (from EU).

medjohn

請問有分音器套件賣嗎？

ccli1996

medjohn 發表於 2013-7-18 23:40
請問有分音器套件賣嗎？

Ching,
Hope this shop in GZ that can fulfill your request.
http://www.imageaudio.cn/

ayuen

medjohn 發表於 2013-7-18 16:44
Is there any focal jm lab driver or Seas speaker available in hk?
Thanks

Medjohn兄，

我地三個人用seas單元做左三對呢套喇叭，單元喺廣州敖士買

http://www3.hiendy.com/hififorum ... ;extra=&page=87

medjohn

ccli1996 發表於 2013-7-19 00:14
Ching,
Hope this shop in GZ that can fulfill your request.
http://www.imageaudio.cn/

Thanks so much!

medjohn

ayuen 發表於 2013-7-19 04:08
Medjohn兄，

我地三個人用seas單元做左三對呢套喇叭，單元喺廣州敖士買

請問你設計的分音器很難做嗎？我想學做，但不知從何學起

halfnew

我都想知邊度有分音器电路板賣

ayuen

medjohn 發表於 2013-7-19 07:52
請問你設計的分音器很難做嗎？我想學做，但不知從何學起

我用俗稱'搭棚'方式銲接分音器，懂得銲接就應該可以

ayuen

halfnew 發表於 2013-7-19 11:42
我都想知邊度有分音器电路板賣

去深水埗鴨寮街

JanHau

我想學銲接技巧

ayuen

JanHau 發表於 2013-7-19 15:43
我想學銲接技巧

等我分享吓自己心得

工欲善其事，必先利其器
- 買個靚D嘅辣雞，有溫度教嘅，銲細微嘢、半導體嗰類用低溫度（280~350度），銲大棚嘢（例如喇叭插好大粒銅，或幾粒零件搭埋）就用高溫度（350~450度）
- For audio，用有2~4% 銀靚錫線，曾有師父話用無銀錫線仲好聲，無謂拗，人地做生意，銲部DAC一千幾佰點，用好多錫，幾佰蚊一卷嘅含銀錫線成本貴好多，佢話更靚聲就更靚聲啦
- 清潔銲點：零件腳會氧化或者有污垢，用2000grit幼沙紙細細力省走表面至銲，如果係鍍金底板，用擦紙膠卒吓，銲每點前亦要清走銲咀上殘留嘅餘錫
- 盡可能搭棚，可以的話，零件腳扣腳一個圈令接觸面增大，令零件腳搭腳直通，唔靠錫（或嗰幾%銀）導通，錫只係扮演黐埋D零件嘅角色
- 銲時盡量唔好超過3秒，否則出現所謂銲'老'D錫，啞晒色（鍍電差左），當然，銲大粒銅喇叭柱呢類大舊嘢無可避免要耐D，無計
- practice makes perfect，當有左技術，一隊埋去就銲到，fix定喺380度銲埋細微嘢都ok，唔會銲老錫或銲壞零件

mike1981

我建議都係買diy 有名既套件玩

因為沒有測量下及不斷嘗試下, 分音好難做得好

我自己測完都改左8次, 重微調緊
因為用球頂中音的關係, 更要中頻下段cross好高

medjohn

mike1981 發表於 2013-7-20 12:06
我建議都係買diy 有名既套件玩

因為沒有測量下及不斷嘗試下, 分音好難做得好

may i know where to buy DIY kit in HK?
Thanks!

mike1981

medjohn 發表於 2013-7-20 12:40
may i know where to buy DIY kit in HK?
Thanks!

香港比較少
taobao有好多seas廠出既套件

madisound都有線路圖, 箱體資料可參考
然後係國內做箱, 買單元就可

一般來說你跟得足
聲音是非常好

好似seas既idunn, ziv two, 國內的clair, clair2, charme


圖左為clair, 右為idunn

terencet

ayuen 發表於 2013-7-20 02:31
等我分享吓自己心得

工欲善其事，必先利其器

袁哥好分享！

ayuen

terencet 發表於 2013-7-20 22:34
袁哥好分享！

Hope this helps